|
||
|
Golden Member
 加入日期: Apr 2004
文章: 2,576
|
回覆: ATA133 排線可裝在 燒錄器光碟嗎?
引用:
燒錄器用ATA133的排線?? 沒必要吧~ 一般CD或DVD燒錄機都只有支援到ATA33而已呀... |
||||||||
2004-04-11, 01:35 AM
#21
|
|
|
*停權中*
加入日期: Feb 2000 您的住址: 台灣
文章: 6,822
|
引用:
心理作用。 |
|||
|
2004-04-11, 09:28 AM
#22
|
|
|
*停權中*
加入日期: Feb 2000 您的住址: 台灣
文章: 6,822
|
回覆: 回覆: ATA133 排線可裝在 燒錄器光碟嗎?
引用:
沒錯, 您說得一點都沒錯！  但, 如果改用 Ultra ATA-133 的排線(80 pin 的密度)感覺爽度是增加了.....  |
|
|
2004-04-11, 09:33 AM
#23
|
|
|
Major Member
加入日期: Apr 2002 您的住址: 彰化逛大街中...
文章: 271
|
我認為燒錄有問題時,排線的安裝是否牢固也要檢查一下,之前因為幫電腦換殼,結果燒錄DVD一直出錯,而再把2端接頭重插後,就又正常了...白白浪費了幾片空片
|
|
2004-04-11, 04:20 PM
#24
|
|
|
Major Member
加入日期: Mar 2004 您的住址: Taipei
文章: 173
|
差很多
Currently, there are two kinds of IDE cables, one is 40 pins, and the other is 80 pins. Only 80 pins cable supports Ultra DMA mode. If you are using 40 Pins cable, the IDE device(HDD or CDROM) will be set into PIO mode. In this mode, CPU issued access commands, then fail into a loop to poll IDE device whether the data were transfer completly. You will see that CPU work in 100% during access IDE device.
For Ultra DMA mode, CPU issued a command, then IDE controller will transfer the data to/from memory. After access complete, it will generate a notice to CPU. Less than 50% will show in CPU usage. For HDD, the data transfer rate is near 30 MB/S - Ultra DMA 3, 50MB/S - Ultra DMA 4, 80MB/S - Ultra DMA5. But less than 10MB/S - PIO. If your CDROM writer support Ultra DMA mode, you should use 80 pins cable(ATA66=ATA100=ATA133 80Pins) If your CDROM write doesn't support Ultra DMA mode, you still can use 80 Pins cable, but the preformance are the same.
__________________
Ray!! |
|
2004-04-15, 08:40 PM
#25
|
|
|
Amateur Member
 
加入日期: Jan 2004 您的住址: 新竹、苗栗
文章: 40
|
引用:
是嗎？真不不容易壞嗎？ 我的黃色排線無緣無故就掛了 我還以為是我的硬碟掛了 換了光碟機的排線才知道是黃色的排線壞了 
__________________
天堂不是一個地方，而是一個時刻，一個幸福的時刻。 |
|
|
2004-04-16, 01:10 AM
#26
|
|
